MSport exhaust tips

mindcontrollerone · 09-10-2018, 03:45 PM

I searched on the forum, online, and measured the best I could! I'm still not 100% sure. Has anyone installed 4 inch round quad tips on the MSport bumper?

Katsumoto · 09-12-2018, 04:10 PM

me

mindcontrollerone · 09-12-2018, 04:11 PM

Quote:

Originally Posted by Katsumoto

me

Did you end up having to cut the bumper? Any pictures?

Katsumoto · 09-12-2018, 04:11 PM

Here is

Katsumoto · 09-12-2018, 04:12 PM

no , straight in

mindcontrollerone · 09-12-2018, 04:20 PM

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Russmov · 09-12-2018, 06:37 PM

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

mindcontrollerone · 09-12-2018, 09:45 PM

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

Russmov · 09-12-2018, 09:54 PM

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

mindcontrollerone · 09-12-2018, 09:56 PM

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

Yes

Russmov · 09-12-2018, 09:56 PM

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

I am also looking to do this, and would like to order some. I posted picture of some in the thread I started earlier but no one was able to tell me if they would work.

Russmov · 09-12-2018, 10:00 PM

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

Yes

Alright thanks. So from exhaust pipe to the inlet is 3" i believe. So any thing with a 3" inlet diameter, up to 4" outlet should work. You know the length by any chance?

mindcontrollerone · 09-12-2018, 10:15 PM

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

Yes

Alright thanks. So from exhaust pipe to the inlet is 3" i believe. So any thing with a 3" inlet diameter, up to 4" outlet should work. You know the length by any chance?

I'm not 100% sure... if I have to slightly modify the bumper I will. I think the 4 inch looks more aggressive and it fills gap much nicer over the 3.5

Russmov · 09-12-2018, 10:20 PM

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

Yes

Alright thanks. So from exhaust pipe to the inlet is 3" i believe. So any thing with a 3" inlet diameter, up to 4" outlet should work. You know the length by any chance?

I'm not 100% sure... if I have to slightly modify the bumper I will. I think the 4 inch looks more aggressive and it fills gap much nicer over the 3.5

I agree the 4" looks better, now just need to find the proper length for them.

mindcontrollerone · 09-12-2018, 10:31 PM

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

Yes

Alright thanks. So from exhaust pipe to the inlet is 3" i believe. So any thing with a 3" inlet diameter, up to 4" outlet should work. You know the length by any chance?

I'm not 100% sure... if I have to slightly modify the bumper I will. I think the 4 inch looks more aggressive and it fills gap much nicer over the 3.5

I agree the 4" looks better, now just need to find the proper length for them.

I think any reputable exhaust shop can make any length work. The inlet is showing 2.8 for the X5, most of the tips I like are 2.5. I'll call my muffler shop tomorrow and see if they can make it work.

Russmov · 09-12-2018, 10:44 PM

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

Yes

Alright thanks. So from exhaust pipe to the inlet is 3" i believe. So any thing with a 3" inlet diameter, up to 4" outlet should work. You know the length by any chance?

I'm not 100% sure... if I have to slightly modify the bumper I will. I think the 4 inch looks more aggressive and it fills gap much nicer over the 3.5

I agree the 4" looks better, now just need to find the proper length for them.

I think any reputable exhaust shop can make any length work. The inlet is showing 2.8 for the X5, most of the tips I like are 2.5. I'll call my muffler shop tomorrow and see if they can make it work.

Hmm someone posted a while back that inlet diameter was 3". Where did you find the exact diameter?

mindcontrollerone · 09-12-2018, 10:49 PM

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Katsumoto

no , straight in

Awesome! I noticed AC Schnitzer and Hamann both only make 3.5 but GT Haus makes the 4.0. Per GT Haus it requires cutting but their tips are slightly slanted. Thanks for confirming can't wait to get my car done up!

Are these 4" per tip, 8" total per side?
Which did you go with?

I am looking to install two 4 inch on each side. Similar to this

So each tip is 4" correct? So 8" for the two tips together per side

Yes

Alright thanks. So from exhaust pipe to the inlet is 3" i believe. So any thing with a 3" inlet diameter, up to 4" outlet should work. You know the length by any chance?

I'm not 100% sure... if I have to slightly modify the bumper I will. I think the 4 inch looks more aggressive and it fills gap much nicer over the 3.5

I agree the 4" looks better, now just need to find the proper length for them.

I think any reputable exhaust shop can make any length work. The inlet is showing 2.8 for the X5, most of the tips I like are 2.5. I'll call my muffler shop tomorrow and see if they can make it work.

Hmm someone posted a while back that inlet diameter was 3". Where did you find the exact diameter?

eBay

mindcontrollerone · 09-13-2018, 02:35 PM

@Russmov

Didn't realize you have a similar thread, lol

I confirmed with my exhaust shop that they can easily stretch 2.5 to 2.8. It would be welded of course.

Russmov · 09-13-2018, 02:40 PM

Quote:

Originally Posted by mindcontrollerone

@Russmov

Didn't realize you have a similar thread, lol

I confirmed with my exhaust shop that they can easily stretch 2.5 to 2.8. It would be welded of course.

No problem!
Also that's good to know it can be fitted. Which tips are you going with?

mindcontrollerone · 09-13-2018, 06:59 PM

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

@Russmov

Didn't realize you have a similar thread, lol

I confirmed with my exhaust shop that they can easily stretch 2.5 to 2.8. It would be welded of course.

No problem!
Also that's good to know it can be fitted. Which tips are you going with?

Still debating... four inch tips for sure though!

Russmov · 09-13-2018, 07:07 PM

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

@Russmov

Didn't realize you have a similar thread, lol

I confirmed with my exhaust shop that they can easily stretch 2.5 to 2.8. It would be welded of course.

No problem!
Also that's good to know it can be fitted. Which tips are you going with?

Still debating... four inch tips for sure though!

Yeah I'm still looking as well. Do you know what length they need to be?

mindcontrollerone · 09-13-2018, 07:15 PM

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

Quote:

Originally Posted by Russmov

Quote:

Originally Posted by mindcontrollerone

@Russmov

Didn't realize you have a similar thread, lol

I confirmed with my exhaust shop that they can easily stretch 2.5 to 2.8. It would be welded of course.

No problem!
Also that's good to know it can be fitted. Which tips are you going with?

Still debating... four inch tips for sure though!

Yeah I'm still looking as well. Do you know what length they need to be?

The short side is 12.2

09-10-2018, 03:45 PM	#1
mindcontrollerone Lieutenant 809 Rep 475 Posts Drives: 2015 M4 / 2015 X5 Join Date: Oct 2012 Location: Los Angeles CA iTrader: (0)	MSport exhaust tips I searched on the forum, online, and measured the best I could! I'm still not 100% sure. Has anyone installed 4 inch round quad tips on the MSport bumper?
	Appreciate 1 Russmov1328.00 Tweet Quote

09-12-2018, 04:10 PM	#2
Katsumoto First Lieutenant 126 Rep 303 Posts Drives: MBB F95 Comp Join Date: Aug 2015 Location: N/A iTrader: (6)	me
	Appreciate 0 Quote

09-12-2018, 04:11 PM	#4
Katsumoto First Lieutenant 126 Rep 303 Posts Drives: MBB F95 Comp Join Date: Aug 2015 Location: N/A iTrader: (6)	Here is Attached Images
	Appreciate 2 mindcontrollerone809.00 hufington3122.00 Quote

09-12-2018, 04:12 PM	#5
Katsumoto First Lieutenant 126 Rep 303 Posts Drives: MBB F95 Comp Join Date: Aug 2015 Location: N/A iTrader: (6)	no , straight in
	Appreciate 0 Quote

09-13-2018, 02:35 PM	#18
mindcontrollerone Lieutenant 809 Rep 475 Posts Drives: 2015 M4 / 2015 X5 Join Date: Oct 2012 Location: Los Angeles CA iTrader: (0)	@Russmov Didn't realize you have a similar thread, lol I confirmed with my exhaust shop that they can easily stretch 2.5 to 2.8. It would be welded of course.
	Appreciate 1 Russmov1328.00 Quote

		BMW X5 and X6 Forum (F15/F16) > BMW X5 (F15) and BMW X6 (F16) Forum > BMW X5 and X6 (F15/F16) Forum
MSport exhaust tips