[F80Boost]

How the fawkkkkkkkkkkkkk do i remove the 12v terminal "round nut with star shaped center" in engine bay on my 435i ?????


I have to connect the jb4 bluetooth 12v power wire to it !!!!

[ronanz]

don't remember exact size, but I think you need a t50 torx bit

.

[primetyme941]

Originally Posted by ronanz

don't remember exact size, but I think you need a t50 torx bit

.

yes 50 torx

[jgoens]

Originally Posted by F80Boost

How the fawkkkkkkkkkkkkk do i remove the 12v terminal "round nut with star shaped center" in engine bay on my 435i ?????


I have to connect the jb4 bluetooth 12v power wire to it !!!!

Dude, have you read anything as far as instructions, or anything other than the answers to your questions on this forum? After reading the install guide, after I learned I needed a T50 which I did not have, I went to the local auto store and picked one up.

[Buckeyes]

Hope he reads the instructions on what map to run or very expensive mistakes will happen

[jgoens]

Originally Posted by Trcb777

Hope he reads the instructions on what map to run or very expensive mistakes will happen

I'm starting to think, the only thing he goes by is what we say..which is good info, but c'mon, do some basic research. Here's the advice: go to N54tech and read the sticky and then ask the questions.

[F80Boost]

Originally Posted by jgoens

I'm starting to think, the only thing he goes by is what we say..which is good info, but c'mon, do some basic research. Here's the advice: go to N54tech and read the sticky and then ask the questions.

i have read everything!!!!!!! wtf !!!

the instrructions for connecting the bluetooth from bms, basically have a photo that says "connect here"_____________>>>>> and point to battery 12v post...........

so yeah, it wouldve been nice to know t his before hand that i needed special tool, wtf!!!





i rread thru alll the instructions etc, so when u guys are trying to bash me and say i didnt, doesnt make sense..............

prime example........nobody had in the INSTRUCTIONS " be careful with 12v battery terminal in engine bay......that minor overlook , could cause soemthing to get fried!!!!!

and of course , they added it to the instrcutions, AFTER IT HAPPENED TO MULTIPLE PPL...


so yeah, i ask questions, and LOTS OF THEM, to make sure i cover everything........

not trying to start an argument here, so plz dont take it that way.....




well, now my line of questioning will begin with datalogging, and tuning, the JB4 i just installed!!!!!!!!!

[BimmerFan]

Originally Posted by F80Boost

i have read everything!!!!!!! wtf !!!

the instrructions for connecting the bluetooth from bms, basically have a photo that says "connect here"_____________>>>>> and point to battery 12v post...........

so yeah, it wouldve been nice to know t his before hand that i needed special tool, wtf!!!





i rread thru alll the instructions etc, so when u guys are trying to bash me and say i didnt, doesnt make sense..............

prime example........nobody had in the INSTRUCTIONS " be careful with 12v battery terminal in engine bay......that minor overlook , could cause soemthing to get fried!!!!!

and of course , they added it to the instrcutions, AFTER IT HAPPENED TO MULTIPLE PPL...


so yeah, i ask questions, and LOTS OF THEM, to make sure i cover everything........

not trying to start an argument here, so plz dont take it that way.....




well, now my line of questioning will begin with datalogging, and tuning, the JB4 i just installed!!!!!!!!!

Dude, calm down that attitude won't get you far here. Do lots of reading, I mean "a lot of reading" on the forums. You'll be surprised how many times you'll answer your own questions before you even ask. Lord knows how many hours I have spent here just reading up stuff without even needing the information yet. Also get very familiar with some basic hand tools if you want do your own installations. Not taking jabs at you either. Just saying.

[yoandry]

Originally Posted by BimmerFan

Dude, calm down that attitude won't get you far here. Do lots of reading, I mean "a lot of reading" on the forums. You'll be surprised how many times you'll answer your own questions before you even ask. Lord knows how many hours I have spent here just reading up stuff without even needing the information yet. Also get very familiar with some basic hand tools if you want do your own installations. Not taking jabs at you either. Just saying.

This is almost a month old. He should be calmed down by now.

[BimmerFan]

That proves my point. I just read. I did not mention I pay attention to the dates..lol. As you were.

[platty]

I just used channellock pliers...